Oil & Gas Solution

Oil and natural gas are important energy resources. Therefore, there is an urgent need to build a comprehensive security system to enhance the energy industry in all aspects of standardized management, monitoring, early warning, and accident investigation, so as to prevent accidents. At the same time, there is high demand to build infrastructure which provides timely and accurate information to rescue workers, improving the efficiency of rescue work and minimizing loss.

  • Oil Field Video Surveillance
  • Intelligent Perimeter Protection
  • Intelligent Entrance Control for Vehicles
  • Production Area Surveillance

Related Videos

Oil & gas

Hardened networks for wells, pipelines, terminals and refineries

Oil and gas operators need reliable data from remote wellheads and pipelines, safe and secure plants, and connected crews in the field. Navijin delivers industrial switching, long-range wireless, thermal video and gateway-based remote management built for hazardous, isolated sites.

Industrial
DIN-rail PoE switching
Thermal
Bi-spectrum temperature monitoring
Up to 4 km
Point-to-point wireless links
Auto-recovery
Gateways with watchdog design

The challenge

What this network has to handle

Remote, isolated assets

Wellheads, block valves and pump stations sit far from fibre and staff.

Extreme conditions

Desert heat, sand, humidity and corrosive atmospheres attack electronics.

Safety and early warning

Overheating equipment, leaks and intrusions must be detected early, around the clock.

Converged operations

SCADA, CCTV, voice and enterprise systems share infrastructure but must stay isolated.

Solution architecture

An end-to-end Navijin design, layer by layer

  1. L1

    Wellhead & skid edge

    Industrial unmanaged PoE switches inside RTU and camera cabinets, with DIN-rail power.

  2. L2

    Plant switching

    Managed PoE switches in plant control rooms aggregate cameras, access points and operational systems into separate VLANs.

  3. L3

    Site gateway

    A gateway with an integrated PoE switch and AP controller provides routing, Internet access control and auto-recovery for camps and remote offices.

  4. L4

    Long-range wireless

    Point-to-point bridges connect wellpads and gathering stations to the nearest fibre node.

  5. L5

    Thermal & perimeter video

    Bi-spectrum thermal cameras measure temperature in real time. IP67 bullets protect fences and gates.

Business outcomes

What you gain

01

Earlier detection

Thermal monitoring and video analytics flag problems before they escalate.

02

Fewer site visits

Remote access and self-recovering gateways reduce trips to remote assets.

03

Safer crews

Reliable voice and data across camps and work areas.

04

Contained risk

OT, CCTV and IT segmentation limits the impact of cyber incidents.

How we deliver

From site survey to handover

  1. 01

    Site survey & requirements

    Our engineers review floor plans, cable routes, user density, camera counts and power, then agree on measurable targets for coverage, bandwidth and uptime.

  2. 02

    High- and low-level design

    You receive a documented design: topology, VLAN and IP plan, PoE power budget, Wi-Fi channel plan and a bill of materials using Navijin part numbers.

  3. 03

    Staging & configuration

    Switches, gateways and access points are pre-configured and labelled before shipping, so installation on site is fast and repeatable.

  4. 04

    Installation & commissioning

    Certified partners install, test and document every link. Wi-Fi is validated with a post-installation survey and camera views are signed off with you.

  5. 05

    Handover & lifecycle support

    As-built documentation, admin training, firmware guidance, warranty and RMA handled through Navijin and our authorised partners.

FAQ

Frequently asked questions

Are Navijin products certified for hazardous (Ex) zones?

Standard Navijin switches and cameras are not Ex-certified. In classified zones they must be installed in certified enclosures, or outside the zone, according to your site's hazardous-area rules. Our engineers design around these constraints.

What is a bi-spectrum thermal camera used for?

It combines a thermal sensor with a visible camera. Operators can see temperature anomalies such as overheating motors or flare issues alongside a normal image for context. The ICB-N3785 measures temperature in real time with up to 0.3 °C accuracy.

How do remote wellpads connect to the control room?

Usually over point-to-point wireless to the nearest fibre node, or over 4G LTE where coverage exists, with a VPN back to the central network.

Plan your network with Navijin engineers

Share your floor plans or site layout. We return a design, bill of materials and budgetary quotation, usually within a few working days.