Switching · 7 min read · 12 November 2026
How to Calculate a PoE Power Budget (With Worked Examples)
Learn how to calculate the PoE power budget for IP cameras, Wi-Fi access points and phones, avoid night-time camera reboots and choose the right PoE switch and power supply.
Power over Ethernet (PoE) is one of the most convenient technologies in networking, and one of the most commonly mis-sized. A classic symptom is cameras that work perfectly during the day and reboot at night. When infrared LEDs switch on, power draw rises and the switch runs out of PoE budget.
This guide shows how to calculate a PoE budget properly, with worked examples for cameras, access points and phones.
Step 1: Know the PoE standards
| Standard | Name | Max power at switch port | Power at device |
|---|---|---|---|
| 802.3af | PoE | 15.4 W | 12.95 W |
| 802.3at | PoE+ | 30 W | 25.5 W |
| 802.3bt Type 3 | PoE++ | 60 W | 51 W |
| 802.3bt Type 4 | PoE++ | 90 W | 71.3 W |
The difference between switch-port power and device power is lost in the cable. Budget at the switch side.
Step 2: List every device at its maximum draw
Use the maximum consumption from each datasheet, not the typical figure. For cameras, this means IR on and heaters on where fitted. For access points, it means all radios active.
Step 3: Add headroom
Add 20–30% to the total. Headroom covers ageing, temperature, future devices and measurement differences.
Step 4: Check both limits
Check two limits:
- Per-port limit: each port must supply its device's maximum, for example 30 W for PoE+.
- Total budget: the switch's total PoE budget must exceed the sum of all devices plus headroom.
Worked example 1: 16 IP cameras
Sixteen 4 MP IR bullet cameras with a datasheet maximum of 8 W each:
- 16 × 8 W = 128 W
- +25% headroom = 160 W
A 16-port PoE+ switch with a total budget of at least 160 W is needed. Check the datasheet of models such as the GE1610-16P2SF.
Worked example 2: Office floor
- 6 Wi-Fi 6 access points at 15 W = 90 W
- 20 IP phones at 5 W = 100 W
- 4 dome cameras at 6 W = 24 W
- Total 214 W, +25% = about 270 W
A 24-port managed PoE+ switch with 10G uplinks and a budget above 270 W fits, for example the GE7722-P28X4-L3. Check the exact budget in the datasheet.
Worked example 3: Industrial cabinet
An outdoor cabinet with an industrial 8-port PoE switch, four cameras at 10 W and one access point at 20 W:
- PoE load: 60 W
- Switch's own consumption: around 10 W (check the datasheet)
- Total 70 W, +30% = 91 W, so choose a 120 W DIN-rail supply such as the DRP-120-48.
Common mistakes
- Using "typical" instead of maximum power.
- Forgetting IR, heaters and PTZ motors.
- Ignoring the switch's own consumption when sizing external supplies.
- Assuming every port can deliver full power at the same time.
- Exceeding 100 m of cable without a long-range PoE switch. See our PoE solutions.
Need help?
Navijin engineers can size PoE budgets and power supplies for your project. Send your device list via our sales team.
FAQ
Frequently asked questions
How much headroom should a PoE budget have?
Add 20–30% to the total maximum consumption of all powered devices.
Why do my cameras reboot at night?
Usually because IR LEDs raise power consumption at night and the switch exceeds its total PoE budget.
Related
Keep reading
PoE networking solutions
Read more →PoE vs PoE+ vs PoE++
Read more →Choose a PoE switch for cameras
Read more →Private 5G vs Wi-Fi for Enterprises: Which Wireless Technology Fits?
Compare private cellular networks and enterprise Wi-Fi for factories, ports, campuses and warehouses: coverage, mobility, device support, spectrum, cost and when to combine both.
Read more →What Is Port Security on a Switch? Stop Unknown Devices From Connecting
Switch port security explained: limiting MAC addresses per port, sticky learning, violation modes (protect, restrict, shutdown), when to use it and how it compares with 802.1X.
Read more →Warehouse and Logistics Network Design: Scanners, Cameras and Automation
How to design networks for warehouses and logistics centres: Wi-Fi for scanners and vehicles, outdoor yards and docks, CCTV, industrial switches for automation, and resilience.
Read more →Need help designing your network?
Navijin engineers provide free design consultations, bills of materials and quotations for business projects.